The Coleman Mach Adapter Wiring Kit for Advent Air RV Air Conditioners # ACCOLKIT is a plug-in-play adapter that will allow you to use the Advent Air RV Air Conditioner # ACM150 with your Coleman a/c set-up. It includes the needed connections for this to work.
The Coleman Mach Adapter Wiring Kit for Advent Air RV Air Conditioners # ACCOLKIT will not work on Coleman Mach 6000 or 7000 series ceiling vent assemblies, and it will not work with heat pump models. I am not sure what model of... view full answer...
The Timbren Front Suspension Enhancement System part # TGMFP30W which is a fit for a 1984 Winnebago Chieftain is mostly for support but can also be used to help produce a more comfortable ride by absorbing road shock and improving roll stability per Timbren. There is also a kit for the rear, the Timbren Rear Suspension Enhancement System part # TGMRP30. view full answer...
The Air Lift Air Spring Kit part # AL81560 that you referenced has been confirmed as a fit for your 1999 GMC P30 motorhome for the front axle. For the rear axle you would want the part # AL57203.
I attached a set of installation instructions for the part # AL57203, but for the # AL81560 I attached pictures of the install sheets for you to check out. view full answer...
Timbren springs do have the reputation for creating a stiffer ride. The best solution to soften up the ride is to use air bags. For the front axle on your 1988 GMC P30 chassis you can use # AL81560. For the rear use # AL57203 (Note: Designed for vehicles with a GVWR less than 14,500 lbs.)
Then you could add a dual path compressor system, # AL25856, so you can adjust the air pressure from the comfort of the vehicle cab. A dual path would be needed since the front and rear air bags have... view full answer...
I may have a solution for you, but there is not a custom fit hitch for this vehicle so it may require some fabrication. With that said, you may be able to make one of our universal RV hitches like the # 5350, which is adjustable to fit frames 24 to 46 inches wide and comes with mounting hardware included. This hitch will have a maximum capacity of 500-lbs TW/5000-lbs GTW, but will allow you to carry some accessories, like a bike rack at the front of your RV.
I've linked a review video... view full answer...
I recommend going with Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers # AL88203 for your rear axle. This kit is confirmed to fit your 1984 P30. These air springs have built-in jounce springs so that you get the adjustability of air bags but also the comfort of jounce springs. Another nice way to look at it is that you will have a fail-safe backup plan if the air bags lose pressure in some unfortunate event. For a compressor I recommend Air Lift WirelessAIR... view full answer...
You are correct in that your 1988 Gulf Stream Sun Vista is on a GMC P-30 chassis therefore the correct steering stabilizer for you is the Roadmaster Reflex Steering Stabilizer part # RM-RBK3-RSSP30 as long as you have coil spring suspension in the front. If you have leaf spring suspension in the front then we do not have a steering stabilizer for you at this time.
The Reflex Steering Stabilizer will work to help you maintain control of your motorhome by tightening the steering. It comes... view full answer...
You'll be fine even though you measured from edge to edge. You may just end up with a little bit of extra fabric in the corners when installing your Solera Family Room for RV Awnings # LC362235. You will however need to verify that your awning is one of the following models to ensure fitment:
Solera Classic, Hybrid, and Solera 12V power awnings
Carefree Fiesta, Spirit, Pioneer manual, Traveler, and Eclipse 12V power awnings
Dometic Sunchaser, 8500 manual, Weather Pro, and 9100 series 12V... view full answer...
I do have a great option for you, however the Draw-Tite Max-E-Loader Trailer Hitch Receiver # 41121 isn't going to fit your 1995 GMC P3500. This particular hitch is designed for certain model years of the Chevy and GMC full size van and it's not going to line up to the frame rails of your P3500.
There isn't a similar custom hitch available for your vehicle so your best option is to go with a universal weld-on unit like the Draw-Tite # 41990 paired with the 7" # 4907 or 16" # 4916 Weld-On... view full answer...
For your truck Buyers Products Hitch Plate with Pintle Mount # 3371809055 is the correct kit. This is designed to fit Chevy/GMC 2500/3500 trucks with a dump bed like yours so this would be exactly what you'd need. view full answer...
The AirLift LoadLifter Ultimate 5000, part # AL88203 will fit the 1994 P-30 chassis if the motorhome has a GVWR less than 14,500 lbs.
If your motorhome has a different GVWR, let me know and I'd be happy to check with our vendors to see if they have anything compatible. view full answer...
It's generally recommended that you use a weight distribution hitch any time your trailer is greater than 1/2 of the tow vehicle's GVWR; this isn't a hard and fast rule, but it's definitely something that is going to help create a safer and more comfortable towing experience. Weight distributing hitches come either with integrated sway control or without a sway control system.
It sounds like you've already got sway control bars installed on your trailer, so using something like the Reese... view full answer...
We only put those etrailer stickers on the ones we photograph for the website. The Optronics Trailer Clearance or Side Marker Light w/ Reflector item # MC48AB you receive will not have the sticker. view full answer...
The Optronics Trailer Clearance or Side Marker Light w/ Reflector item # MC48AB is the amber lens version of the Red Lense Optronics item # MC48RB you referenced.
These lights measure 3-15/16" long x 1-7/8" tall x 1/2" deep and the distance between mounting holes is 3-3/8". There is not a direct replacement available for your Bargman 68 SAE-P2-A81 clearance lights, however the Optronics Trailer Clearance lights have comparable dimensions. view full answer...
I went out to the warehouse and measured the Empire Faucets RV Kitchen Faucet w/ Pull-Down Spout # EM42HR and measured 14-1/2" from the threads to the end of the longer water lines, and 5-1/2" from the threads to the end of the shorter water line.
I have attached an installation video as well as a diagram for you to check out as well. view full answer...
For a 1988 GMC P-3500 RV, I show that you will need two 16" blades. For you I recommend the Rain-X Latitude Windshield Wiper Blade # RX5079274-2. These are very solid graphite-coated rubber blades, with the Rain-X water repellant coating. view full answer...